Your Trusted Partner for Industrial & Commercial Electronic Repairs Your Trusted Partner for Industrial & Commercial Electronic Repairs

Repair Videos

Repair Videos

Below is a selection of items we have repaired for customers

Parker PA08T-133 Repair - Came with blank screen

Parker PA08T-133 Repair - Came with blank screen, would not POST
.
https://www.SAOelectronics.com
...

GE Main Control Board OEM WB27X24320 08080752 WB02X11300

Repair of GE Main Control Board OEM WB27X24320 08080752 WB02X11300

Complaint: Fan Stuck On.
Repair completed. Tested all functions, including auto-on in high temp events and overheat recovery.

https://www.SAOelectronics.com
...

Dometic Duo-therm 4 Button Thermostat Replace or Rebuild Push Buttons 3106463007

Get a kit here: https://www.ebay.com/itm/186364079567


https://www.SAOelectronics.com
...

QSC K12.2 K10.2 K8.2 SIG LEDs Stuck on - No sound Fix - Signal Lights On

Quick video without Audio running through a quick common fix on the K.2 Series Amplifier Modules K12.2 K 10.2 K8.2.

Just playing with OBS Studio and using the microscope and bench camera at the same time.

.
https://www.SAOelectronics.com
...

Parker PA06S-133 Digitizer replacement and Calibration

Parker PA06S-133 Digitizer replacement and Calibration

.
https://www.SAOelectronics.com
...

Ford F5JL-12A297-DA for Genie lift, inspection before repair

This unit arrived with the complaint of firing on 2 of 4 cylinders on the same bank. Upon opening it up there are obvious signs of corrosion and water damage. We will need to strip the conformal coating from the board, wash it, and reflow all solder once completed, we will determine if the 2nd bank output transistor that is corroded is salvageable.
.
https://www.SAOelectronics.com
...

ICON/Proform MC 2100-12A Repaired and Tested

The customer said their treadmill starts up and stops immediately. Replaced shorted Q2 and tested. All other motor control components test good.

.
https://www.SAOelectronics.com
...

England Stove PU CB93 Repair Testing

This Engalnd's pellet stove controller came in with the auger stuck on and no control over the auger duration and blower speed. Also had no response to the shutdown button. Replaced TRIACs, a few other parts and cleaned the unit.
.
https://www.SAOelectronics.com
...

GE Fanuc - Quick Panel JR QPJ2D100L2P Repair

This unit arrived with no display and a stained digitizer. Repaired torn ribbon cable and replaced digitizer.
.
https://www.SAOelectronics.com
...

Dometic Duo-therm thermostat repair 3106463007 3109228

Common repair on these Thermostats.

https://www.saoelectronics.com
...

Englander 25-PUF pellet stove repair

Customer sent this unit in stating that Englander helped them diagnose this unit down to either a bad thermocouple or bad board. Customer ordered and sent the new thermocouple with the unit to be tested and repaired if necessary. TRIAC on igniter circuit was shorted and the Gate pin was separated from the package. This short caused the igniter to be on, even in the off state.

We had already diagnosed this controller with a bad TRIAC prior to starting this video recording.
.
https://saoelectronics.com/product-category/pellet-stoves/

PU-CB04, PU-CB98, PU-CB19, CPM-CB07, PU-CB240
...

Hayward ECOMMAND 4 GLX-PCB-HPC-4 Running Slow - RTC & Crystal replacement

Our customer replaced the Supercapacitor (backup battery) and noticed his clock was still running slow. We removed his supercapacitor, RTC clock IC, and Crystal and floating decoupling capacitor. Cleaned board and installed all new parts.
.
https://www.SAOelectronics.com
...

HE693OIU357 Keypad Verification

HE693OIU357 Keypad Verification after repairing tactile domes
.
https://www.SAOelectronics.com
...

ESAB Welder Repair

Stuck factory trimmed lead under conformal coating, shorting Output to ground. Likely intermittent since flexing the boar breaks the connection.

https://www.SAOelectronics.com
...

PV300121 Viking Professional Downdraft Board

Uncommon repair, The customer stated that a tree fell on a power line and destroyed every electronic device in their home. On this Viking board, they had a few burned traces and a varister that did it job to protect the board as best it could. While we were at it we recapped the board. 2 of the 3 caps tested questionable.
.
https://www.SAOelectronics.com
...

Another Englander Repair for PU-CB240-06 for 25-PUF Pellet Stove

Another Englander Repair, this unit came in with a shorted TRIAC on the room fan and a non-working keypad. Bad keypads are becoming more and more common, they are not sold by englander, we had our own made. All units are fully tested on our benches using 100w incandescent bulbs. TRIACS require a load to be tested correctly; you can't just throw a meter across the hot and neutral output; they require a load to be measured in the off state and variable voltage state. The bulbs represent: igniter, combustion fan, bottom auger, top auger, room fan. We repair these Englanders for a flat rate fee of $155, no matter what it needs. Repair prices on other brands are also flat rate. www.SAOelectronics.com SAO Electronics

.
https://www.SAOelectronics.com
...

Fire-Lite MS-9050UD Repair

This board came in with a direct short to ground. I replaced the regulator and some shorted TVS diodes. We will not factory reset this unit since it came from a working environment.

https://www.SAOelectronics.com
...

Crestron TPS-200L Could not see the screen at all

A customer sent in this Crestron TPS-200L with a common "dead screen" complaint. Often we can just replace the CFCL backlights on these, This one was a little different than most of these Crestron units.

Replaced LCD and transferred digitizer from old LCD to new LCD.

https://www.SAOelectronics.com
...

Parker CTC PA06S-133 Screen Repair

This unit came back after repair for a touchscreen issue. Found extra touch screen adhesive coming into contact with the touch area. Screen screws were difficult to remove, may have contributed to seeping adhesive.

https://www.SAOelectronics.com
...

Englander Pellet stove Controller Repair 25-EP Stove

The unit came in with No Auger motion; repaired and tested this single auger unit.

https://www.SAOelectronics.com
...

Another "No Power" QSC K.2 Series with a bad solder connection. K8.2 K10.2 K12.2

We did the standard upgrades and upgraded firmware while we were repairing the "factory bad" solder connection. 6th bad solder connection on these thiss month, so far..
.
https://www.SAOelectronics.com
...

Parker PA210T-133 Repair - Dead/Unresponsive

Mian board repair and full test on this unit. Display, Ethernet, USB, RS232/RS422, RS485. Headed back to the customer.
.
https://www.SAOelectronics.com
...

Englander Pellet Stove Control Panel Repair PU-CB19 PU-CB04 PU-CB98

Unit came in with no keypad response. Repaired, tested all functions and headed back to the customer.

Englander
10-CDV, 49-SHC22, 49-TRC22
10-CPM, 49-SHCPM, 49-TRCPM
25-CAB80, 55-SHPCAB80, 55-TRPCAB80
25-CBEP, 55-SHPCBEP, 55-TRPCBEP
25-CBPAH, 55-SHPCBPAH, 55-TRPCBPAH
25-PDVC, 55-SHP10, 55-SHP10L, 55-TRP10
.
https://www.SAOelectronics.com
...

Parker CTC PA10T-133 Repair

This HMI arrived and would boot intermittently. Once it would boot, it was erratic and often lag or became unresponsive. We repaired unit and tested all functions: Touch input, touch calibration, KB input, mouse input, RS232, RS422, RS485, TCP/IP, CF Boot, and Net Boot.
.
https://www.SAOelectronics.com
267650
...

Icon Fitness MC1618DLS Treadmill control board Repair

This unit came in with no output to the drive motor. After restoration, the unit passes all tests. It will be full load tested before shipping back to the customer.
.
https://www.SAOelectronics.com
...

Hayward Goldline GLX-PCB-MAIN Time Repair and Cell Repair

We Repaired the common burn spot on board and replaced Cell relay that was melted. The customer was also worried about the clock losing time, so we cleaned the board and replaced the "backup battery"(Supercapacitor). Tested time for 6 hours, and it maintained time again. RTC and crystal were still encapsulated in a good conformal coating.

Hayward GLX-PCB-MAIN
G1-066008N-1
G1-011004R1
G1-015008R-10

https://www.SAOelectronics.com
...

Englander Upper Auger Issues

After repair, customer stated upper auger would not run. RMA test shows that with no safetys in place upper auger runs. Informed customer to check for a closed exhaust. If vent is closed the air flow vacuum sensors will not trigger. This is required to detect air flow for safety reasons. ...

Parker CTC PA06S-133 No Boot Repair & Digitizer Replacement

We got this unit back up and running, fixed BIOS boot issues, replaced the backlight, and replaced the missing touch glass/digitizer.

Parker CTC PA06S-133
.
https://www.SAOelectronics.com
...

PCB Zodiac Jandy AquaLink OneTouch, LCD, R0550800 9238-133 Repair

This unit came in dead. We replaced the backlight and LCD. All 4 LEDs on the backlight were bad, and the LCD common was open circuit. It obviously got a power surge.

https://www.SAOelectronics.com
...

Whitfield Advantage PSC120A-3605 Repair

This Whitfield Advantage II PSC120A-3605 came in with startup issues, blinking LEDs even with the thermostat calling for heat. The customer also stated that often, it wouldn't do anything at all.

Repaired.

https://www.SAOelectronics.com
...

Englander Pellet Stove 25 Control panel repair PU-CB240

This unit came in with several startup issues; after repairing some stuck keys, burned traces, and bad capacitors, it's back up and running.
.
https://www.SAOelectronics.com
...

GE WB27X10866 Microwave Repair -Dim VFD and select knob not working

Replaced the select knob and rejuvenated the VFD display.

.
https://www.SAOelectronics.com
...

Klipsch R-112SW Repair

Bench testing this Klipsch R-112SW Repair before load testing and hooking to audio analizer.

We replaced needed caps and did resistor upgrade to keep the heat away from the affected capacitors.

https://www.SAOelectronics.com
...

Icon Health MC2100LT Treadmill Module Repair.

Using external PWM to test bench functionality of this module. We will connect DC motor to test full load operation before shipping back to the customer.

https://www.SAOelectronics.com
...

AutomationDirect EA1-T4CL Repair

Unit came into the shop smelling pretty burned up. Rebuilt power supply circuit and tested functionality using Automation Directs C-More Micro programming software.

https://www.SAOelectronics.com
...

Johnson Controls 24-10902-0 fan control board repair

This unit came in dead. We have repaired all faults and shipped it back to the customer.

Johnson Controls 24-10902-0 fan control board repair
Enivro Tec Fan Relay Board OEM PC-01-0134
.
https://www.SAOelectronics.com
...

Parker CTC PA06S-133 Repair

Parker CTC PA06S-133 Repair - Came in non-functional.

https://www.SAOelectronics.com
...

Woodward 9907-205 Repair

This Woodward 9907-205 unit, like many, came in dead. We are able to repair these units and get them back out within 24 hours.

https://www.SAOelectronics.com
...

RCF HD35-A HD 35-A Power Amplifier Repair

This unit came in dead. Needed Mosfets, oscillator and a a few other parts replaced. Replaced all questionable capacitors as well. We will do I/O sound analysis and stress test it for 2 hours then ship it back to the customer.

http://www.SAOelectronics.com
...

AutomationDirect EA1-T6CL Repair

This unit arrived DOA. Appears to have had over voltage on supply or reversed supply voltage. Repaired circuit and tested.

https://www.SAOelectronics.com
...

Hoshizaki Ice Maker Control Board Repair 2A1410-01 2A1410-02

Water-damaged board. Replace logic IC and re-programmed. Replace several other parts to get this customer back up and running. Same-day service.

https://www.SAOelectronics.com
...

NuVo NV-P3500 Repair - No Power & Red Zone Lights

Arrived dead, repaired and had zone issues. Now back up and running.

www.saoelectronics.com
...

NuVo NV-P3100 Repaired.

Like most NV-P3100 and NV-P200 whole house audio systems, this one came in dead. repaired same day and headed back to the customer tomorrow.

www.saoelectronics.com
...

QSC 12.2 Repaired after abuse at Burning Man 2023

This is 1 of 2 that Died after being run on a generator at Burning Man. Both u it's also look like they were fully submerged in mud also.

Generator ran out of gas or was bogged down. SMPS can only do so much work trying to maintain secondary voltages before they heat up and die.

The customer did not want them cleaned.

https://www.SAOelectronics.com
...

GE Main Control Board WB27X24320 Repair 08080752

Light Stuck on the Fan would not run - Repaired

https://www.SAOelectronics.com
...

Whitfield Advantage II Pellet Stove Controller Repair PSC120A-3926 25220801 12155900R 12055902

Sequencing Repaired

https://www.SAOelectronics.com
...

Ready for Repair?

Click below to get started,  Our mail-in form is quick and easy to get your repair started!
LET'S GO!
SAO Electronics
2764 Pleasant Rd Suite A #10114
Fort Mill, SC 29708
linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram